DIY: Screenprinting. A tutorial.

Do It Yourself Screen Printing!

I have developed a cheap and dirty method of screen-printing...and I have had SOO much fun with it, I wanted to share it with anyone who is interested! I have been screen-printing for my ETSY shop katyandzucchini.etsy.com . Check it out to see some ideas of what you can do!

I ordered most of my supplies from Dickblick.com. I have provided links to the items I used, but there are thousands of options out there!

What you need:
Pliers
Picture frame (wood)
Diazo photo emulsion (you can use another brand, but this tutorial uses Diazo)
Diazo sensitizer (comes in a kit with the emulsion and some emulsion remover, all for about $20)
Gauzy drapery (you can always find this at Value Village)
Staple gun
Staples
Cardboard
Thumbtacks
Glass slightly smaller then the picture frame opening
Lamp/light bulb fixture
Light bulb (the more watts, the better!)
Screen printing ink (I use Speedball textile ink)
Timer/clock
Something to print on! Some ideas: t shirts, baby clothes, umbrellas, mirrors, cards, tights, underwear, luggage, pillowcases...

What would be NICE to have, but not absolutely necessary: Reflector light fixture (you can find these at a hardware store OR a pet shop...used for reptile cages)
BBA BULB - 250W
Squeegee
Glass cutter (to use to cut the glass from your frame so it can be used to hold down your image. If you don't cut the glass, it will be too large to set inside the opening and against the screen fabric.)
Screen printing fabric (I use 12XX multifillament fabric, works great!)
Transparency film (you can buy these by the sheet from kinkos)
Copier or printer capable of printing on transparency film



Step 1: Stretching the screen.
For this part, you will need: Picture fame (soft wood), gauzy fabric/screen printing fabric, staple gun and staples, pliers.

• Start by removing all the hardware from the picture frame using the pliers. Remove tacks, hangers, glass, cardboard, etc.

• Once you are down to just the wood frame, you are ready to measure out your fabric.











• Cut a rectangle of fabric that is about 2-3 inches longer then your frame in each dimension. Make sure you leave plenty of fabric, as you will need to be able to grab it and pull it tight.

• Lay your frame on top of the fabric so the flattest side is facing up (it is much easier to staple on a flat surface).












• Wrap the fabric around one edge, place a staple in the center of the side.











• Pull the fabric tight DIRECTLY opposite from the first staple (really tight), and place a staple.












• Move to the adjacent side and repeat.

• Continue adding staples in this manner all around the frame. Pull nice and tight!











• Once the fabric seems secure and tight, trim the excess fabric.












• Use a hammer to sink any staples that are sticking up.











Step 2: Spreading the emulsion
For this part you will need: Diazo Photo Emulsion, Diazo photo emulsion sensitizer, stretched frame (see step 1), squeegee/cardboard with a straight edge, dark space to let your screen dry, newspaper to keep your surface clean.

• First, follow the instructions for mixing your photo emulsion. For Diazo photo emulsion, you will fill the sensitizer (small bottle) ½ up with cold water. Mix the water and sensitizer, then pour into the larger bottle of emulsion. Mix well.













• Lay out newspaper or cardboard. This can get messy!

• Keep the room dimly lit, but make sure you can see...

• Place your frame on the newspaper and pour a bead of Photo Emulsion along one edge of your screen (make sure you choose an edge that is longer than your squeegee).











• Use the squeegee to spread the emulsion evenly across the surface.











• Flip the screen over and continue to spread the emulsion. Keep spreading on each side until the emulsion looks evenly coated. If there are spots that need more emulsion, it’s ok to add more.











• Once the emulsion is evenly spread, set the frame down with the staples resting on the table.

• Place a thumbtack in the four corners of the frame. This will allow you to let the screen dry without sticking to the surface. (This allows the ‘bottom’ of your screen to dry smooth and even).











• Put the screen in a dark place (I use a cupboard, then hang a blanket over the cupboard and turn out the lights…but you could use a cardboard box, Rubbermaid container, etc. You want to keep it as dark as possible).











• Let the screen dry. This can take 24-48 hours depending on the temp/humidity. If you want to speed this up, you can use a fan. Keep the screen cool, as heat will set the emulsion! Room temperature is fine.











• Place any extra emulsion in the fridge, it will last about 4 months if you keep it cool.











• Clean up your mess! Warm water should do the trick.


Step 3: Selecting your image/design
For this tutorial I will explain how to print any image from your computer to burn onto your screen, however you can draw your own design on transparent plastic/glass for a simpler process. You could also cut a design out of opaque paper and use that!

For this step you will need: Transparency film, printer, image on your computer

• Select your image . The image you select must be black and white only (not gray scale). Don’t worry, you won’t have to print with only black ink, but the purpose of the transparency and printed image is to block light from reaching your screen.











• Print your image on paper to make sure it is the size you want it (it should be small enough to fit inside the frame with about an inch of space on each side).

• Load the transparency paper into your printer and print two copies of your image (if it will fit, print two on one page, you can cut it in the next step).











• Once you have two copies, you will overlap the two to make your image opaque (you don’t want any light to pass through). Use clear tape to keep them overlapped.














• Cut the transparency film so it will fit into your frame.

Step 4: Exposing your screen
For this part, you will need: Light fixture and light bulb (using a reflector fixture and a BBA BULB - 250W will significantly cut down the time needed to expose your screen!), your image (see step 3), timer/clock, glass piece large enough to cover your image (but small enough to fit inside the opening in the frame).

• Place black cardboard on your work surface. You don’t want light reflecting off the surface and exposing your screen.

• Keep the room dimly lit.

• Hang your light approximately 12 inches from the work surface.

• Lay out your image and the glass piece, get them ready to place on your screen.

• Get out your screen (make sure the emulsion is dry by touching the surface in one of the corners). Remove the thumb tacks.

• Place your screen on the black paper, directly under the light. The frame should be placed with staples facing up, the fabric in direct contact with the black paper.

• Quickly place your image on the screen, center it and be sure it is straight. (Although the room is dark, make sure you can see well enough to check that your image isn’t reversed…) Place a square of glass on your image to hold in in direct contact with the fabric. If you don't have a piece of glass small enough to fit inside the frame, you can tape your image down.














• Use this chart (http://www.reuels.com/reuels/Silk_Screen_Printing_Instructions.html) to determine your exposure time.

SPEEDBALL SCREEN PRINTING SYSTEM
Recommended Exposure Chart (Revised 1/77)

---

150 Watt Bulb, Clear Incandescent

---

Screen Size . 150W Bulb Height . . Exposure Time

---

8"x10" . . . . . . 12 inches . . . . . . . . . . . . 45 minutes
10"x14" . . . . . 12 inches . . . . . . . . . . . . 45 minutes
12"x18" . . . . . 15 inches . . . . . . . . . 1 hr. 14 minutes
16"x20 . . . . . . 17 inches . . . . . . . . . 1 hr. 32 minutes
18"x20" . . . . . 17 inches . . . . . . . . . 1 hr. 32 minutes

---

BBA No. 1 Photoflood (250 Watt)

---

Screen Size . . Lamp Height . . Exposure Time

---

8" x 10". . . . . . 12 inches . . . . . 10 minutes
10"x14". . . . . . 12 inches . . . . . 10 minutes
12 "x 18" . . . . .15 inches . . . . . 16 minutes
16"x2O" . . . . . 17 inches . . . . . 20 minutes
18"x2O" . . . . . 17 inches . . . . . 20 minutes

PLEASE NOTE:

This chart has been prepared using an aluminum foil pie-plate reflector. More sophisticated light sources, reflectors and equipment can, of course, be used. However, as any variable is changed, you will have to adjust the exposure times and distances. This will require experimentation.

• Turn on the light for the amount of time indicated on the chart. I use a reflector fixture 12 inches from the surface, with an XX light bulb, and I expose an 8X10 inch frame for 4 minutes. I messed around a bit with exposure times, and found it work the best for me. You might have to experiment a little. Too much exposure can set ALL the emulsion, and no ink will be able to pass through. Too little exposure might not set the emulsion well, and all of it will wash off.














• After exposing the screen, immediately take the screen to a sink/tub/hose. The more spraying pressure, the better! Try to keep the screen from being exposed to too much light during this process. I turn out the lights in the bathroom and use the hall lights to help me see.

• Rinse the screen with room temperature water. DO NOT USE HOT WATER! Remember that heat will also set your emulsion! You can use your finger to lightly scrub where you want the emulsion to wash out.

• It might take several minutes to see your image start to appear, but don’t lose hope. The more pressure you can spray on the screen, the faster the unset emulsion will rinse out. I have a 'water pick' in my shower, and it sprays a super strong stream. Works great!











• Once it seem like your image is ‘clean’ (meaning the emulsion has rinsed out), hold your screen up to the light to be sure you didn’t miss any spots.

• Let your screen dry completely.

Step 5: Making your print(s)
For this part you will need: ink (use fabric/textile ink if you are printing on clothing), squeegee or a piece of cardboard with a flat edge, something to print on, your screen (see step 4), cardboard.

• Test your screen on a piece of paper first (I will describe how to print on a t-shirt, but you can print on just about anything!)

• Lay your shirt out flat.. Place a piece of cardboard inside the shirt directly under where you will print your image.












• Place your screen on your t-shirt. Align the image to where you want your print. I use the transparency image to get a good idea of what it will look like...











• Use a piece of cardboard to scoop out some ink and spread a bead along one edge of the screen.











• Use one hand to hold the screen steady. It might help to have an assistant hold the screen on your t-shirt for your first few times.

• Use the other hand to draw the squeegee over the bead of ink and all the way to the other end of the screen. You will use quite a bit of pressure while squeegeeing…this takes some practice. Try to use even pressure the whole time.











• Carefully lift the screen from your t-shirt. Let the ink dry (follow any directions given to 'heat set' the ink to your fabric. Speedball requires you to iron the image to heat set it, so it is machine washable).











• You have your print! Do it again on another shirt, or card, or scarf, or your wall…you just might get carried away. I know I did!











• Be sure to rinse your screen with warm water after you are finished. Let your screen dry flat. It can be reused MANY times! Or…you can use diazo photo emulsion remover to remove all the emulsion, and start over again at step 2!

Here are some ideas for some things you can print on! The sky is the limit!